Fiat 500 Replacement Key Fob
If your remote key fob isn't working, it's time to replace the battery. If you replace the battery and it isn't working it could be a problem elsewhere.
United Locksmith specializes in the creation of new keys for classic automobiles. We have all the tools and parts necessary to perform this service.
Dead Coin Battery
A dead battery is the most frequent cause of your Fiat 500 keyfob not locking or unlocking the doors. The key fob contains the battery of a coin-cell that can quickly deplete when it isn't frequented enough. If your remote began to show signs of weakness such as a loss in range or stopped working completely it is likely that the battery is dead.
The battery inside the key fob is held in place with metal clips for retaining. If the clips are loose, they could cause problems with contact, which can prevent your remote from receiving power. With a small flathead screwdriver, pry the retaining clip outwards to remove the current battery, and replace it with a brand new one. Be sure to use an identical replacement battery kind of voltage, the same size, and specification as the original battery.
Water exposure can cause the key fob to corrode or become damaged. Even a brief bath in soapy water may harm the electronic chip within. Keep your key fob dry.
Water Damage
Water damage could be the cause of your key fob's inability to function properly. Key fobs come with rubber seals that prevent them from being damaged by a light rain or splashes of water. However, it is very important to keep your keys safe from the pool, ocean and the washing machine!
The key fob comes with an electronic chip which sends an electronic message to the immobilizer system of your car. The chip allows the 500 to be locked and started. If it gets wet it will not work.
If you're looking to determine whether your key fob still functioning, you can clean the internal electronics using isopropyl or an electronic cleaner. However, fiat car key cutting is probably recommended to purchase a replacement from a dealer instead of trying to repair an item that is submerged in salt water.
While a replacement fob can cost you a little bit of money, it is much less expensive than having to pay for your Fiat 500 to be towed to the dealer and repaired! In addition, you can do it yourself with only a few steps. Make sure you have the correct battery type before you attempt to open your key fob. You can find step-by-step instructions for any car keyfob on the internet.
Faulty Chip
The chip that is contained in the key fob communicates with your car's immobiliser unit to make sure the vehicle is only capable of starting when the correct key is inserted. If the chip is damaged, or damaged in any way, your car will not start.
Damage to the water or a dead battery are the two most frequently cited reasons for the chip being damaged. It is best to hand over the repair to a professional locksmith, who will be able to replace the chip in a short time and at a a reasonable price.
If your key fob does not work after exposure to clean rain or tap water take the battery off. Wipe down the electronic component using a towel. If the key fob fails to work it's most likely an issue with the chip and is required to be replaced.
Some people will visit their dealer if they need a new Fiat fob. However, this can be an expensive option. If you're looking for a low-cost solution to have your Fiat key fob fixed then look no further than United Locksmith. We have all the tools and expertise to fix your Fiat fob in a professional and timely manner.
Faulty Receiver Module
Fiat key fobs send a signal up 50 feet to the vehicle, which will open and lock the doors (and start the vehicle for vehicles with automatic transmissions). However, there are some things that can cause the fob to cease functioning. This can be caused by a dead coin-battery water damage, worn-out buttons as well as a receiver issue. signal interference, or a malfunctioning chip.
If the fob is in a pocket that has experienced extreme trauma, like falling on hard floor or getting washed in a washing machine, it may not be capable of communicating with the car's Body Control Module (BCM). The BCM is a security device that will only accept signals from genuine original keys.
If this is the case, you will need to replace your fob. A professional locksmith can handle the entire key replacement process including programming a new key for your 500. They can even give you a clone fob that works exactly the same way as the original (and costs less than the cost).